72" / 1829mm Kampf Foil Slitter/Separator: FS-125
Foil Slitting/SeparatingVery Good 72" Kampf Foil Slitter/Separator: FS-125 / Complete Line / Individual Components can be sold separate of the complete line
SPECIFICATIONS
Manufacturer:
- Kampf / model RKW-1003 / new 2001
Material:
- Aluminum and its alloys
- Alloys = 1100, 3003, 7072, 8111
- Temper = 0 - H19
Entry Web Width:
- 25 - 72" (635 - 1829mm) (see note at Slitter below)
Web Thickness:
- .002 - .015" (0.05 - 0.381mm)
Slitting Widths / Tolerance / Cuts:
- 0.6" - 46" (15.8 mm - 1169mm)
- +/- .004" (0.1mm) slit width tolerance
- Maximum of 40 Cuts Plus Edge Trim
Edge Trim min/max:
- 0.5" - 2.0" per Side (12.7 - 50.8mm)
- Edge Trim Scrap handling = Suction, chopper, transport, air separator, diverter gate, vacuum hose, and maintenance platform
Slitting System:
- Scissors Cut
- Optional Square Knife conversion would allow .037" (0.93 mm) can lid stock - and - .081" (2.06 mm) dead soft, 0 temper aluminum
Line Speed:
- 2600 fpm max (800 mpm)
- Depends on material type, thickness, spool size, core size, and slit width
Exit Reels Diameter
- OD max: 72" (1829 mm)
- OD min: 18" (457 mm)
- Depends on material type, thickness, spool size, core size, and slit width
Spool/Core ID:
- 6", 10", 12", 16", 20" Dia. (152, 254, 304, 406, 508 mm)
- Fiber Core (Cardboard)
Operational Speeds
- Jogging = 10 mpm approximate (Adjustable)
- Acceleration/Deceleration = Vo - V Max. in approx. 80 seconds
- Instantaneous Stop = V Max - Vo in approx. 40 seconds
- Emergency Stop = V Max - Vo in approx. 10 seconds
Winding Tensions
- Unwind = Max. 12.650 N
- Rewind 1 = 318 - 6328 N / 25% Taper Tension at Outer Diameter
- Rewind 2 = 318 - 8438 N / 25% Taper Tension at Outer Diameter
EQUIPMENT / EQUIPPED WITH:
Unwind Coil Car:
- The car advances the coil thru the scrap prep station and to the main unwind
- In either manual or automatic mode.
- V-saddle is a turntable and rotates up to 180 deg. the coil as needed
Scrap Rewinder
- Coil preparation station with rewind stand
- Pneumatic radial clamping with air wrench
- Pusher plate to eject coil onto Prep Butt Table
Prep Butt Table:
- Table transports scrap butts away from the line for removal
- Hydraulic cylinder raises and lowers the table
- Hydraulic motor driven rollers to move the scrap butts
Coil Magazine #1:
- Prep station unwind station holds the coil and allows it to unwind onto the scrap rewinder
- Spool sizes, 66 to 72" and TBD
- Drive motors move the mandrel to unwind the metal
Coil Magazine #2:
- Coil holding stand to hold the coil until ready to slit
- Spool sizes, 66" to 72" and TBD
- Driven spool length compensator to adjust for spool length
Main Unwind Reel:
- Fixed gear AC motor powered
- Electro pneumatic brakes / Inch Brake for maintaining web tension / Servo Motor for maintaining web tension during slitter operation / Hydraulic cylinder core length adjustment / Chucks are graduated for different I.D's / Ultrasonic coil tracking sensor
Unwind Coil Size:
- OD max = 90" (2286 mm)
- OD min = 24" (610 mm)
- Spool Size (ID x OD x Face Length)
- 1. 23.75" x 26" x 72" (603 x 660 x 1829 mm)
- 2. 12.812" x 16" x 66" (325 x 406 x 1676 mm)
- 3. 12" x 16" x 27.50" (304,8 x 406 x 698,5 mm)
- Unwind & Coil Stands designed to accept future spool length of 76" (1930mm)
Splice Table:
- Allows operators access to the coil ends for threading and splicing.
- Idler rolls to feed the metal thru the splice station; 3 idler rolls
- Splice platform provides personnel access to the station
- Clamping bars to secure the metal; 3 pneumatic actuated clamping bars
- Automatic cross cutting device, motorized traverse
- Taping is done manually via 50mm wide 3" core tape spools
Automatic Threading Bar:
- Leads the attached metal from the splice table thru the slitting cassette
- Threading chain pulls the threading bar back and forth thru the line
Butt Conveyor and Spool Storage:
- Carries spool or spool and butt away from the unwind stand
- Includes Roller table and Lift out device
Stretcher Rolls:
- Elongation (Stretch) = 1.5 - 3.0% with a target of 2.0%
- Rolls secure, stretch, guide and apply tension to the metal thru the slitter
- Entry rolls adjust up and down on operators side
- 3 Nip rolls hold tension against the stretching rolls
- Transport rolls feed metal thru the slitter rolls, hold tension and adjust the wrap angle of the metal in the slitter
- Rolls 3,4,6, and 8 independently driven.
- Transports 1 & 2 drive 7 rolls each and control tension
- Transports 5 & 7 drive 2 rolls each and control tension
- 3 Stretch rolls stretch and harden the metal through the slitter
- Stretch rolls have a special coating
- Stretch rolls have incrementally smaller sizes as the metal progresses downstream (3 graduated sizes for 1%, 2% or 3% stretch, configured largest to smallest)
- 2 Clamping rolls prevent metal from springing back into zone 2 and auto thread two exit rolls (one at each rewind)
- 3 Contact measuring rolls use load cells to take pressure reading for tension calculations and absorb shock and supply backup force at the rewinds
#1 = at the entry to zone 2, has 2 load cells
#2 and #3 = one at each rewind, pneumatically powered compensating rolls on a dancer system
Texturing Roller Unit:
- Applies light lubricant coat to heavy gauge foil before slitting
Electrostatic Oiler:
- Five (5) heated tanks
- Supply different liquids and/or wax to the electro-static applicator bar
- Closed loop blade heating system
- Strip enters thru the bottom of the oiler enclosure
- Two (2) spray bars (one top and one bottom)
- Blades set by air actuated valves, vary width in 4" increments (28" to 72" widths)
- Fluid reservoir
- 1600W immersion heater
Tank Farm:
- Tank 1 = lubricant XL-301
- Tank 2 = lubricant PL-1043
- Tank 3 = lubricant PL-1027
- Each tank stand includes: 1 x 25gal Base tank, 2 x 5gal Batch tanks for mixing lubricant with lecithin additive, and 1 x 5gal additive tank for storing lecithin
Slitting Cassette:
- Top knife shaft = adjusts both horizontally and vertically (secured jet nuts / top knife set, 2 holders, knives, snap ring, spring)
- Bottom knife shaft = stationary (secured by jet nuts / bottom knife set, knives, rounded edge spacer)
- 2 knife shaft support rollers on each arbor
- Felt knife pads, one for each knife
- Cross cutting device (automated, traverse motor, 2 heads, injector set rails, manual operation)
Suction Unit:
- Transports scrap from the slitter to the baler
- Adjustable pull rolls (8)
- Adjustable shifting suction nozzles (2 large and 2 small)
- Pushers, close unused suction nozzles, 4 pushers
- Flexible metal hose for transport to bifurcated pipes which transport scrap strip
to scrap baller
Scrap Choppers:
- Chop scrap in the suction tubes
- 4 total in-line suction tubes
- 4 spare suction tubes as spares
Rewind Reels:
- 2 separate rewind reels, that accept spools, diameters below
- 2 separate non-driven winding rolls contact metal for tight wraps
- Fully automatic cross cutting device
- Rewind shafts expansion
- Both Rewinds are driven by independent AC Motors, each drive stand has 2 motors (one small and one large)
- Quick change hydraulically chucked mandrel connections
- Winding Shafts:
2 Rewind Shafts - 6" (152mm)
2 Rewind Shafts - 10" (254mm)
2 Rewind Shafts - 12" (305mm)
2 Rewind Shafts - 16"(406.4 mm)
Rewind Coil Cars:
- 2 separate cars for each rewind stand
- Hydraulic lift
- Hydraulic motor travel
- See-saw lay-on arm: pivots to rest on top of the coil
- Clamping arm: secures the end of the coil for transport
Machine Design:
- Drive side on the right, as seen in material running direction
Power:
- Voltage: 480 Volts + 10%-20%, AC-3 Phase, 60 Cycle +/- 2%
- Control Voltage: 24 Volts
- Total Supply amount: approx. 700 Kva
- Power cabinet was powered up and all drives fired up 02-2023
- PLC Program copy is available
Air:
- Continuous Pressure: >/- 5,5 Bar (>/- 77 Psi)
- Consumption approx.: 24 Nm3/H
Water:
- Flow: 1,5 M3/H (53 Cu Ft/H)
Drive / Controls:
- Siemens drives, motors, & SPS, Siemens PLC w/ modem, software
Sold EXW "as is" off foundation and in good-dry storage.
- Line removed from service 2020
- A thorough Condition Inspection Report performed by Kampf is available. Please request it.